TPS2546RTER · Texas Instruments · Independent distribution
Source TPS2546RTER with SZIME Electronics for USB Charging Port Projects
Connect your TPS2546RTER purchasing requirement with the correct TI documentation, package details and project delivery needs through SZIME Electronics.
Published · Updated
When TPS2546RTER is already specified in a design, the next step is to translate that exact requirement into a clear purchasing enquiry. The complete order code, quantity, packaging and delivery date all belong in the same conversation. SZIME Electronics supports TPS2546RTER sourcing through independent distribution, helping purchasing teams discuss the required material alongside the technical information that identifies it. Send a single component request or include it within a broader BOM.
Understand the device you are requesting
Texas Instruments identifies the TPS2546 family as a USB charging port controller with power switching and load detection. It combines charging control with an integrated high side MOSFET and a switch for the USB 2.0 data lines. The device supports charging modes associated with USB Battery Charging Specification 1.2, making it relevant to compatible USB port designs in hosts, hubs and charging equipment.
For purchasing, the important starting point is TPS2546RTER in full. The family name leads to the technical documentation; the complete order code identifies the item to be discussed in the quotation, purchasing records and material review. Keeping that distinction clear gives engineering, procurement and the assembly team a shared reference.
| Item | TI reference information |
|---|---|
| Requested order code | TPS2546RTER |
| Manufacturer | Texas Instruments |
| Device role | USB charging port control with integrated power switching and load detection |
| Package | 16 pin WQFN with the TI package code RTE |
| Nominal package body | 3.00 mm by 3.00 mm |
| Operating supply range | 4.5 V to 5.5 V |
| Technical document | TPS2546 datasheet SLVSBJ2C Revision C |
Match the order code to the packaging requirement
TI lists TPS2546RTER with a standard large tape and reel quantity of 3,000, while TPS2546RTET is listed with a smaller carrier quantity of 250. These are manufacturer packaging references. For an SZIME enquiry, state the quantity you need and the acceptable supplied packaging so the quotation can address both. If full reels are required for the build, make that requirement explicit at the start.
Treat the approved order code as a controlled field throughout the purchasing process. Ask for the same code on the quotation and review the proposed material information against it. If another ordering option is proposed, have the responsible team review the difference before accepting it. This keeps a packaging discussion connected to the component actually approved for your product.
Use the original technical documents for design review
TI's datasheet is the reference for pin functions, operating modes, current limit configuration, layout guidance and electrical conditions. Its package documentation provides the corresponding mechanical details. Engineers can use these resources to check the approved schematic and PCB footprint, while purchasing teams use the orderable part information to confirm the requested package and carrier.
It is useful to keep the engineering revision and the procurement requirement together. If a design change alters the package, operating conditions or approved component list, pass that update to the buyer before the next enquiry. For an existing production design, identify the exact approved component and any restrictions on alternatives. This helps prevent a later clarification from interrupting the purchasing decision.
Turn a component request into a useful quotation enquiry
SZIME's English TPS2546RTER page provides a direct route to an enquiry for the exact code. You can also contact the team by email. Include enough information to connect the sourcing discussion with the way the material will be purchased, reviewed and used. The following details make a strong starting point.
Exact order code TPS2546RTER and the quantity required for the current purchase.
Target delivery date and destination country, with any later build quantities shown separately.
Required packaging, batch preferences and any material review documents your team expects.
Whether the enquiry is for an approved production BOM, a new project or replenishment.
Current availability, the proposed batch, packaging and delivery arrangements can then be discussed for the actual request. If TPS2546RTER is one of several outstanding lines, send the wider list and mark the parts that determine the build schedule. This gives SZIME a clear view of the purchasing scope and your immediate priorities.
Connect this purchase with the next production stage
A component enquiry can also begin a continuing supply discussion. Tell SZIME if the present quantity supports an initial build, a production release or a recurring requirement. Where several releases are planned, share the expected sequence and indicate which quantities are confirmed. SZIME's wider BOM and project supply services allow the conversation to include other component needs and later procurement stages.
Discuss TPS2546RTER or your next USB project with SZIME
Ready to source TPS2546RTER? Send the complete order code, required quantity and target delivery date to SZIME Electronics. If your USB charging project is still being defined, introduce the application and the decision you need help moving forward. You can begin a project enquiry before the final component list is complete.
Contact SZIME Electronics at sales@szime.cn or visit https://en.cstiot.com for component sourcing and project enquiries. Shenzhen, China.